---------------------------------------------------- Intense2Drv Intergraph Intense2Drv Display Driver for Windows NT Workstation ---------------------------------------------------- ------------- Legal Notices ------------- Copyright 1997, Intergraph Corporation. All rights reserved. Including software, file formats, and audio-visual displays; may be used pursuant to applicable software license agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright and trade secret law and may not be provided or otherwise made available without proper authorization. Restricted Rights Legend Use duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 or subparagraphs (c) (1) and (2) of Commercial Computer Software -- Restricted Rights at 48 CFR 52.227-19, as applicable. Unpublished -- rights reserved under the copyright laws of the United States. -------------------- End of Legal Notices -------------------- ------------------- Version Information ------------------- Product: Intense2Drv Number: SHBY355AC-0403A Version: 04.03.02.01 Date: 20-OCT-1997 Description: The Intergraph Intense2Drv Display Driver provides support for the Intense 3D Pro 1000, 1000-T, 1000-G, 1000-GT, and Intense 3D Pro 2200, 2200-T, 2200-G, 2200-GT, 2200S, 2200S-T, 2200S-G, 2200S-GT display adapters. The geometry accelerator supported in the "-G" configurations above is limited to part number MSMT382. This release of the Intergraph Intense2Drv Display Driver will install and run only systems running Windows NT 4.0. This driver supports Multisync video monitors as well as Intergraph's 20, 21, and 27 inch Multiple-Sync InterVue monitors. -------------------------- End of Version Information -------------------------- Installation Help ================= The Intergraph Intense 3D Display Driver utilizes the Intergraph Intense 3D Pro 1000 and Intergraph Intense 3D Pro 2200 graphics accelerator cards on Pentium, Pentium Pro and Pentium II workstations. This driver will not run on the Intergraph 433, 466, or any other machine which does not have PCI backplane hardware. Additionally, the machine must have 3.3 volts on the PCI bus (or a separate 3.3 volt power connector) and provide support in the BIOS for VGA behind a PCI bridge. See MANIFEST.TXT for list of delivered files. To retrieve this version of the Intergraph Intense2Drv Display Driver, use the floppy provided or insert a blank formatted floppy into drive A: and copy all files listed in the MANIFEST.TXT file onto the floppy. WINDOWS NT 4.0 SETUP - PLEASE READ CAREFULLY! --------------------------------------------- 1. Log into the system as using an account that has Administrator privileges. 2. To select the Intergraph Intense2Drv Display Driver, select the Display icon of the Control Panel. 3. Choose the "Settings" Tab. 4. Select the "Display Type" button. 5. Select the "Change" button. 6. Select the "Have Disk" button. 7. A dialog will appear asking for the full path for the OEM display driver files. The default path given will be A:\ Select "OK" when ready. 8. A dialog will appear indicating the driver to be loaded. The selection should be "Intergraph Intense 3D". Choose "OK". 9. A dialog will appear asking to proceed with the third party driver installation. Choose "YES". 10. A dialog box should appear telling that the drivers were successfully loaded. Select "OK". 11. Select the "Close" button on the "Display Type" dialog. 12. Select the "Close" button on the "Display Properties" dialog. 13. A final dialog box pops up at this point with the message that the display settings have changed and restarting Windows NT will be necessary for the new settings to take effect. If you have an Intergraph InterVue monitor then select "No" and change the monitor type per the following instructions. Otherwise, select "Yes". 13a. Re-select the Display icon of the Control Panel 13b. Select the "Intergraph Monitor" Tab and choose the Intergraph InterVue monitor. 13c. Select the "Close" button on the "Display Properties" dialog. 13d. Reboot the system. NOTE: Remember to eject floppy before shutdown. 14. The Intergraph Intense2Drv Display Driver will be loaded during system boot and display at the 640 x 480 resolution. However, if an Intergraph driver has been previously installed, the resolution will be the last one selected. After logging on, the resolution can be changed in the "Display Properties" dialog. 15. Following the system shutdown and subsequent logon, a dialog will appear stating that the current settings are invalid. This dialog appears the first time you logon every time you change the display driver. Select OK and configure the display settings as desired. 3D STUDIO MAX 1.x USERS - PLEASE READ CAREFULLY! ------------------------------------------------ The Intergraph Heidi Device Driver, glzihdd.hdi, is developed for the Intergraph Display Driver that accompanies it on the installation media. As a general rule, you should always update the Heidi driver to match the current display driver. Using a Heidi driver that does not exactly match the version of the display driver may result in system hangs and/or poor performance. For example, the Heidi driver built for Windows NT 3.51 will cause a system hang if used on a system running WIndows NT 4.0 and a 4.0 version of the display driver. The OEM Setup for the display driver will copy the Heidi Device Driver, glzihdd.hdi, to your %SystemRoot%\system32 directory. Once 3DSMAX is installed on your system, move glzihdd.hdi from %SystemRoot%\system32 to the "DRIVERS" sub-directory of the 3DSMAX product. For example, if you have installed 3DSMAX to the root directory of your C: drive, you should copy glzihdd.hdi to C:\3DSMAX\DRIVERS as follows: > copy %SystemRoot%\system32\glzihdd.hdi C:\3DSMAX\DRIVERS\. Screen Resolution and Refresh Rate Table ======================================== To access the list of available screen resolutions and refresh rates, the "List All Modes..." button on the "Settings" page in Display Properties must be selected. 1. Choose the Display icon in the Control Panel. 2. Select the "Settings" page. 3. Select the "List All Modes..." button to access table of supported screen resolutions and refresh rates. Multiple screens are supported as of the 4.3 release of the display driver. The desktop may now span up to four monitors horizontally, or up to four vertically or be configured in a 2 x 2 arrangement. The monitor configuration is selected on the "Intergraph Monitor" page in the Display Properties applet. The maximum number of pixels in either the horizontal or vertical axis is 4096. Note: NT 4.0 does not support the "Primary Left/Top" feature that was available with NT 3.51. Monitor Selection ================= The "Intergraph Monitor" page in Display Properties must be used to change the monitor type. 1. Choose the Display icon in the Control Panel. 2. Select the "Intergraph Monitor" page. 3. Select the appropriate monitor type. 4. Reboot for the selection to take affect. Support has been added for DDC monitors. To enable use of DDC information from the monitor, select a monitor type of "DDC monitor". DDC information is only retrieved from the monitor at boot time if "DDC monitor" is selected. Stereo ====== To view the supported stereo display modes, the "Advanced" button on the "Intergraph Settings" page in Display Properties must be selected. 1. Choose the Display icon in the Control Panel. 2. Select the "Intergraph Settings" page. 3. Select the "Advanced" button. 4. Select the "Enable Stereo Display" check box. 5. Select the desired stereo display mode. Only modes supported by the currently selected monitor will be available for selection. 6. Select "OK" to close the "Advanced Configuration" dialog. 7. Select "OK" to save all modifications. 8. A dialog will appear indicating that the changes you have made will not take effect until the computer is restarted. Select "OK". 9. Reboot for the selection to take affect. For Frame Sequential Stereo, it is important that the correct Monitor Type (see above for details) be selected before enabling this stereo display mode. If the specific Monitor Type attached to your system is not selected, resolutions that are beyond the capability of this monitor may be available for your selection. If you have not chosen the specific Monitor Type attached to your system, be sure to test an individual resolution before applying it. If you encounter problems, see the "Trouble Shooting" section below. New Features ============ - Support for a desktop that spans up to four monitors. - Support for Frame Sequential Stereo. - Support for Frame Interlaced Stereo. - Support for the GL_EXT_BGRA extension. - Native color mode of RGB vs. BGR is now user selectable. New Hardware ============ - Support for the Intense 3D Pro 2200 graphics series - Support for the Intense 3D Pro 2200S graphics series (version 04.03.01.00) Bug Fixes ========= - Fixed problem in geometry accelerator in which the direction vector for the light could get corrupted. The problem was reported against a particular Pro/E design and trail file. (version 04.03.02.01) - Fixed a problem in which the driver did not recognize the enable/disable state change of individual light sources. This problem was reported as incorrect rendering in the StoneHenge demo. (version 04.03.02.00) - Fixed a problem in which the driver did not recognize the state change when two-sided lighting was enabled/disabled without various other related state changing. This problem was reported as an incorrect color drawn in a Pro/E design file. Problem (version 04.03.02.00) - Display Tab dialog button repositioned for Japanese locale (version 04.03.02.00) - Design Review windows leave dark areas when other windows are collapsed or uncollapsed over it. (version 04.03.01.00) - Fixed query functions to include support for feedback buffer type, feedback buffer size, vertex array enables and selection buffer size. (version 04.03.01.00) - Software cursors (animated and some colored cursors) leave garbage when moved across double buffered OpenGL windows. (version 04.03.01.00) - Last pixel of an image may be displayed with red and blue components of the color swapped. (version 04.03.01.01) - Texture memory associated with unshared textures is not deleted when the OpenGL context is deleted. - Some clipped quads in OpenGL were not drawing at all if only one of the three vertices was in the view volume. - Avoid blue screening when bad addresses and/or sizes are sent to OpenGL for the glReadPixels and glDrawPixels commands. - Microstation circles displayed as ellipses in stereo mode. - Incorrect millimeter pixel size returned by the driver - 3D Studio Max version 1.x (Heidi renderer) bleeds into OpenGL screen savers Trouble Shooting ================ IF YOU BOOT NT AND THE SCREEN DOES NOT SYNCHRONIZE PROPERLY, DO THE FOLLOWING: Reboot the system to NT, but hit the space bar immediately when prompted. Select 'Use Last Known Good' in the Configuration Recovery Menu. This approach assumes the last configuration was a valid configuration, however. If the 'Last Known Good' method does not apply to your case, try the selecting the VGA option from the system boot menu. Selecting this option will boot NT with the VGA driver instead of the GL Display Driver. At this point you can reinstall the GL Display Driver. If all else fails: Reboot the system to DOS and remove the file GLZMPD.SYS in directory %SystemRoot%\SYSTEM32\DRIVERS. Reboot the system again and boot VGA mode. Since the Intergraph Intense2Drv Miniport Driver has been removed, NT will use the Microsoft standard VGA driver. Re-install the Intergraph display driver using the display properties page, select the appropriate Intergraph monitor and reboot the system. Following the reboot, select an acceptable resolution using the display properties page. If your system does not have DOS (NT only), and your installation of NT uses the standard DOS file system (FATFS), you may boot from floppy then remove this file from the system drive. If your NT system was built on OS/2, or if your NT resides on HPFS, you may boot from an OS/2 system recovery (boot) floppy and remove the file. If you have an NTFS-formatted system disk, you will need to reload the NT Operating System (you should choose to not reformat your system disk during reinstallation, in order to preserve your software and data). Customer Support ================ Problems may be logged through the Intergraph Customer Support Center by dialing 1-800-226-4891. An operator will open a worksheet and transfer you to a technical support engineer. Customer Support Center hours are Monday through Friday from 7:00 a.m. to 7:00 p.m. central time. Experience has shown that problem solving is expedited if you supply the following information when first contacting the software support engineer. 1. SOFTWARE CONFIGURATION a. Operating System and driver version and dates. b. Has the system/nucleus software configuration changed recently? 2. HARDWARE CONFIGURATION a. CPU b. Graphics card 3. PROBLEM SPECIFICS. a. How/when does the problem occur? b. What error messages are displayed? c. Does it happen on more than one machine? Intergraph Bulletin Board Service (IBBS) ---------------------------------------- Available to all software customers. IBBS enables you to exchange messages and files with Intergraph's technical and marketing staff, as well as with other Intergraph customers, using a modem. As an added benefit, for U.S. customers with valid maintenance contracts or products under warranty, problem worksheets can be logged on IBBS 1. Connect to the IBBS by setting the communication protocol to eight (8) data bits, no parity, one (1) stop bit, and any baud rate up to 14,400 bps. IBBS phone numbers are 205-730-8786 (up to 14.4K bps) and 205-730-6504 (up to 2400 bps). 2. Once connected to the IBBS, respond to the login request with the appropriate user ID. If connecting for the first time, respond with "NEW" and the IBBS will step through the process of creating a new user ID. 3. The Top menu is the main menu of the IBBS. Select option C ... Customer Services from the Top menu. Then select option W .. Worksheet Problem Logging from the Customer menu. 4. Respond to each question with the appropriate information. Please limit each line of the problem description to a maximum of 60 characters. 5. The IBBS sends the request as an E-mail message from the IBBS user. Verification of the worksheet number, or an error message indicating the failure condition will be returned through E-mail to the IBBS login account. Intergraph Online ----------------- Available to all software customers. Intergraph's information server on the World Wide Web brings you fast, up-to-the-minute information on Intergraph's products and services, as well as the company's direction. Access to Intergraph Online is available using any of the popular Web browsers such as Netscape, NCSA Mosaic, and others. Connect to Intergraph Online at the following Internet address: http://www.intergraph.com If you have trouble accessing Intergraph Online, send an E-mail message to webmaster@intergraph.com.